For medium- to heavy-duty applications, this unit features rollers that reduce friction between the wire mesh and deck, optimizing drive horsepower.

Standard Specifications

• Widths: 12″ – 36″ (Custom Widths Available)
• Standard Speed: 60 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Bottom Mount @ Discharge
• Frame: 12 Gauge x 6-1/2″ Deep
• Bearings: Grease Sealed
• Sprockets: 13 Tooth x 4.1″ Pitch Diameter
• Standard Mesh: 1/2″ x 1″ Galvanized Steel

The Herringbone wear strips are made of stainless steel and are ideal for water, high temperature, and dirty or gritty applications. The unique Herringbone deck pattern spreads the belt-wear evenly across the belt.

Standard Specifications

• Widths: 12″ – 36″ (Custom Widths Available)
• Standard Speed: 60 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Bottom Mount @ Discharge
• Frame: 12 Gauge x 6-1/2″ Deep
• Bearings: Grease Sealed
• Sprockets: 13 Tooth x 4.1″ Pitch Diameter
• Standard Mesh: 1/2″ x 1″ Galvanized Steel

Used in assembly and production lines where a roller chain is needed to reduce friction and allow for heavier loads.

A very rugged, heavy duty hinged steel belt conveyor. Designed for use in extreme heavy duty steel and scrap applications.

Standard Specifications

• Widths: 12″ – 72″ (Custom Widths Available)
• Lengths: Depends on Application (Min. of 8′);
• Standard Infeed: 60″ (Min. of 36″)
• Standard Discharge: 60″
• Standard Speed: 30 FPM
• Standard Motor: 3 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: Structural “C” Channel 3″ x 4.1# x 21-3/4″ Deep; (7 Gauge is also Available)
• Frame Depth: 21-3/4″
• Frame Width: Belt Width + 11-1/4″
• Bearings: Grease Sealed
• Sprockets: 6 Tooth x 12″ Pitch Diameter
• Belt: 6″ Pitch Hinged Steel Belt with 4″ High Cleats on 48″ Centers, 7 Gauge x 4″ High Side Wings, 3″ Diameter x 1.5″ Flanged Rollers, Outside Sidebars
• Supports: Structural “C” Channel; 6″ x 8.2#
• Others: Access Panels, Take up at Infeed, 7 Gauge Siderails
• Available in type 3 (Z), type 4 (L) and horizontal configurations

This unit infeed tapers from 6-5/8″ to 4-1/8″ and then back to 6-5/8″. The very shallow 4-1/8″ section is designed so the unit can fit into a very tight space inside or under an existing machine.

Standard Specifications

• Widths: 12″, 18″, 24″, 30″, 36″, 48″, and 60″ (Custom Widths Available)
• Lengths: Depends on Application
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 15-1/4″ Deep x Formed 10 Gauge
• Drive Shaft Dia.: (M751 = 1-15/16″) (M750 = 2-15/16″)
• Infeed Shaft Dia.: (M751 = 1-11/16″) (M750 = 1-15/16″)
• Bearings: Grease Sealed
• Sprockets: 6 Tooth x 8″ Pitch Diameter
• Belt: 4″ pitch hinged steel belt, one piece apron, with 2-3/8″ high cleats on 24″ centers, 3″ high side wings, 1-3/4″ diameter hardened flanged rollers, outside sidebars, 1/2″ diameter axle with impact tube.
• Available in type 3 (Z), type 4 (L) and horizontal configurations

This unit infeed tapers from 6-5/8″ to 4-1/8″ and then back to 6-5/8″. The very shallow 4-1/8″ section is designed so the unit can fit into a very tight space inside or under an existing machine.

Standard Specifications

• Widths: 12″, 18″, 24″, 30″, 36″, 48″, and 60″ (Custom Widths Available)
• Lengths: Depends on Application
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 15-1/4″ Deep x Formed 10 Gauge
• Drive Shaft Dia.: (M751 = 1-15/16″) (M750 = 2-15/16″)
• Infeed Shaft Dia.: (M751 = 1-11/16″) (M750 = 1-15/16″)
• Bearings: Grease Sealed
• Sprockets: 6 Tooth x 8″ Pitch Diameter
• Belt: 4″ pitch hinged steel belt, one piece apron, with 2-3/8″ high cleats on 24″ centers, 3″ high side wings, 1-3/4″ diameter hardened flanged rollers, outside sidebars, 1/2″ diameter axle with impact tube.
• Available in type 3 (Z), type 4 (L) and horizontal configurations

This unit features a very shallow infeed combined with the strength of a deeper intermediate and drive frame. The shallow 5-3/8″ deep infeed is designed to fit under an existing machine. The remainder of the unit is 6-5/8″ deep. This unique combination provides both strength and space flexibility.

Standard Specifications

• Widths: 6″, 8″, 12″, 18″, 24″, 30″ and 36″ (Custom Widths Available)
• Lengths: Per Application
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 6-5/8″ Deep x Formed 12 Gauge
• Infeed: Semi-Rounded
• Drive Shaft: 1-3/16″ diameter
• Bearings: Grease Sealed, Marine @ Infeed
• Sprockets: 5 Tooth x 4.25″ Pitch Diameter
• Belt: 2-1/2″ Pitch Hinged Steel Belt, One Piece Apron, with 5/8″ high cleats on 12-1/2″ Centers, 1″ high side wings, 1.5″ Diameter rollers (Flanged Rollers are available), Outside Sidebars are required on belts greater than 18″, but also optional for smaller widths.
• Available in type 3 (Z), type 4 (L) and horizontal configurations

This compact but rugged conveyor is the ideal choice for handling very small parts, stampings, scrap, chips and turnings. Its condensed size also allows it to fit into tight spaces too small for a standard 2-1/2″ pitch machine.

Standard Specifications

• Widths: 6″, 8″, 12″, 18″, 24″, 30″ and 36″ (Custom Widths Available)
• Lengths: Depends on Application
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 8-1/2″ Deep x Formed 12 Gauge
• Drive Shaft: 1-11/16″ diameter (The M721 is 1-7/16″ dia.)
• Bearings: Grease Sealed
• Sprockets: 6 Tooth x 5″ Pitch Diameter
• Belt: 2-1/2″ Pitch Hinged Steel Belt with 1-3/8″ high cleats on 12-1/2″ Centers, 1.5″ high side wings, 1.5″ Diameter Rollers (Flanged Rollers are available), Outside Sidebars are required on belts greater than 18″, but also optional for smaller widths.
• Also available in liquid tight bottom pans (model 723)
• Available in type 3 (Z), type 4 (L) and horizontal configurations

This compact but rugged conveyor is the ideal choice for handling very small parts, stampings, scrap, chips and turnings. Its condensed size also allows it to fit into tight spaces too small for a standard 2-1/2″ pitch machine.

This compact but rugged conveyor is the ideal choice for handling very small parts, stampings, scrap, chips and turnings. Its condensed size also allows it to fit into tight spaces too small for a standard 2-1/2″ pitch machine.

Standard Specifications

• Widths: 6″, 8″, 12″, 18″, 24″, 30″ and 36″ (Custom Widths Available)
• Lengths: Per Application
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 6-5/8″ Deep x Formed 12 Gauge
• Bearings: Grease Sealed
• Sprockets: 5 Tooth x 4.25″ Pitch Diameter
• Belt: 2-1/2″ Pitch Hinged Steel Belt, One Piece Apron, with 7/8″ high cleats on 12-1/2″ Centers, 1″ high side wings, 1.5″ Diameter Rollers (Flanged Rollers are available), Outside Sidebars are required on belts greater than 18″, but also optional for smaller widths.
• Also available with liquid tight bottom pans, (model 726)
• Available in type 3 (Z), type 4 (L) and horizontal configurations

The Model 716 is the non-liquid-tight version of the Model 715.

Standard Specifications

• Widths: 4″ – 24″ (Custom Widths Available)
• Lengths: 3′ – 20′ (Infeed = 12″ /Discharge = 18″)
• Curves: 30°, 45° and 60°
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 4-1/8″ Deep at Infeed; 6-5/8″ Deep, Lower Curve thru Discharge x 14 Gauge
• Bearings: Grease Sealed at Discharge; Press in Bronze Bushings at Infeed
• Sprockets: 10 Tooth x 4.854″ Pitch Diameter
• Belt: 1-1/2″ Pitch Hinged Steel Belt, One Piece Conventional 14 Gauge Apron, with 5/8″ high cleats on 12″ Centers, 12 Gauge x 3/4″ high radial side wings, 7/8″ x 1/2″ wide Flat Face Rollers, 12 Gauge Outside Sidebars
• NOTE: Conventional Belt Only
• Available in type 3 (Z), type 4 (L) and horizontal configurations

This compact but rugged conveyor is the ideal choice for handling very small parts, stampings, scrap and chips. Its condensed size is ideal for tight spaces too small for a standard 2.5″ pitch machine.

Standard Specifications

• Widths: 4″ – 24″ (Custom Widths Available)
• Lengths: 3′ – 20′ (Infeed = 12″ /Discharge = 18″)
• Curves: 30°, 45° and 60°
• Standard Speed: 30 FPM
• Standard Motor: 1/2 HP 230/460/3/60 TEFC
• Standard Drive: Top Mount, Right Side
• Frame: 4-1/8″ Deep at Infeed; 6-5/8″ Deep, Lower Curve thru Discharge x 14 Gauge
• Bearings: Grease Sealed at Discharge; Press in Bronze Bushings at Infeed
• Sprockets: 10 Tooth x 4.854″ Pitch Diameter
• Belt: 1-1/2″ Pitch Hinged Steel Belt, One Piece Conventional 14 Gauge Apron, with 5/8″ high cleats on 12″ Centers, 12 Gauge x 3/4″ high radial side wings, 7/8″ x 1/2″ wide Flat Face Rollers, 12 Gauge Outside Sidebars
• NOTE: Conventional Belt Only
• Also available in a non liquid tight bottom pan (model 716)
• Available in type 3 (Z), type 4 (L) and horizontal configurations